Show all

CONSTRUCTION OF AN INDUSTRIAL BARROW

5,000

ATTENTION:

BEFORE YOU READ THE CHAPTER ONE/ABSTRACT OF THE PROJECT TOPIC BELOW, PLEASE READ THE INFORMATION BELOW.THANK YOU!

 

INFORMATION:

YOU CAN GET THE COMPLETE PROJECT OF THE TOPIC BELOW. THE FULL PROJECT COSTS N5,000 ONLY.

THE FULL INFORMATION ON HOW TO PAY AND GET THE COMPLETE PROJECT IS AT THE BOTTOM OF THIS PAGE. OR YOU CAN CALL: 08137701720

 

 

CONSTRUCTION OF AN INDUSTRIAL BARROW

 

ABSTRACT

 

An Industrial barrow was produced which would aid in conveying heavy materials in the laboratory and industrial set up.

 

It was made from mild steel that was cut to dimension, made into shape and coupled to form the desired outstanding barrow.  Details are shown in chart (fig 1) containing the picture representation.

 

Some of it’s dimensions are;

 

Bucket            –           Area of 816.3 in2

 

Carriage         –           Ø 1.3in x 63.65in

 

Stand             –           1.7in x 27in

 

Braces            –           1.5in x 12.5in;   Ø 0.72 in x . 9.5in

 

Rim                 –           Ø 9.5in

 

Shaft              –           Ø 2in x 10.3in

 

TABLE OF CONTENTS

 

CHAPTER ONE

 

Introduction

 

CHAPTER TWO

 

Literature review

 

CHAPTER THREE

 

Fabrication procedure

 

Material of construction

 

Design consideration

 

Construction procedure

 

Project drawing

 

Costing of standard wheel barrow

 

CHAPTER FOUR

 

Discussion

 

Precautions

 

Recommendations

 

Conclusions

 

References.

 

CHAPTER ONE

 

INTRODUCTION

 

One should be able to get familiarized with the industrial barrow; its design, uses or function and areas of demand.

 

ILLUSTRIATION: An industrial barrow can be classified under a second order lever; considering the L.E.F. (Load, Effort and Fulcrum) positions.  The weight or load being in between the effort and fulcrum tells a typical second order lever, the effort being applied at one and which is the handle of the barrow (helps one to lift the load);

 

The wheel being the fulcrum and the bucket which serves as the load or weight (where the object would be placed upon).

 

DESIGN:        The barrow was constructed having in mind the end of which it would be used.  Practically, the barrow is meant to carry loads which ordinarily would be difficult to carry by ordinary human strength.

 

In this technology, it was found out that is could to a considerable cheight, ease the labour to which one has to go through in his daily activities especially when in the workshop or laboratory when heavy loads are to be conveyed.

 

The design of the wheel barrow has aided main to use a minimal amount of energy to convey heavy materials for distants with the aid of its wheel which when not present would be impossible or might involve more labour force when the barrow are not used.  However, due to its state of function.  It is designed with metal steel so that it can resist the force/weight applied to it.  this is because of its resistively, strength, rigidity and toughness.

 

FUNCTION/USES: The sole aim of constructing on industrial barrow is its usage; to move materials or industrial loads from one point of the factory / industry / laboratory to the other end or from any of these to the other or another destination either for repair or replacement.  This in large extent, reduces cost, saves human strength, time and for convenience.

 

AREAS OF DEMAND:        As the name implies, it is basically an industrial equipment that aid in carrying out functions or tasks which ordinarily cannot be attained if human effort well left to do to alone.  It is very vital that it be kept in proper use to achieve its objectives.  It is also capable of carrying rigid materials/objects which if not used could result in the damage of the spinal cord in young adults (youths).  Thus; it helps to eradicate these problems to some certain extent.

 

HOW TO GET THE FULL PROJECT WORK

 

PLEASE, print the following instructions and information if you will like to order/buy our complete written material(s).

 

HOW TO RECEIVE PROJECT MATERIAL(S)

After paying the appropriate amount (#5,000) into our bank Account below, send the following information to 08137701720

(1)    Your project topics

(2)     Email Address

(3)     Payment Name

(4)    Teller Number

We will send your material(s) after we receive bank alert

 

BANK ACCOUNTS

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 0046579864

Bank: GTBank.

 

OR

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 2023350498

Bank: UBA.

 

 

NOTE:

YOU CAN ALSO MAKE A TRANSFER PAYMENT

 

FOR MORE INFORMATION, CALL:

08137701720

 

AFFILIATE LINKS:

www.easyprojectmaterials.com

www.easyprojectmaterials.net.ng

www.easyprojectsmaterials.net.ng

www.easyprojectsmaterial.net.ng

www.easyprojectmaterial.net.ng

www.academia.edu