Show all

DESIGN AND IMPLEMENT A MICRO CONTROLLER BASED MULTIPURPOSE SECURITY DEVICE WITH DIRECTION CAPABLE OF SECURING A MILITARY CANTONMENT FROM INTRUDER LOCATION AND DETECTION AND TO CONTROL ACCESS TO A STRONG ROOM IN THE CANTONMENT

5,000

ATTENTION:

BEFORE YOU READ THE CHAPTER ONE/ABSTRACT OF THE PROJECT TOPIC BELOW, PLEASE READ THE INFORMATION BELOW.THANK YOU!

 

INFORMATION:

YOU CAN GET THE COMPLETE PROJECT OF THE TOPIC BELOW. THE FULL PROJECT COSTS N5,000 ONLY.

THE FULL INFORMATION ON HOW TO PAY AND GET THE COMPLETE PROJECT IS AT THE BOTTOM OF THIS PAGE. OR YOU CAN CALL: 08137701720

 

 

DESIGN AND IMPLEMENT A MICRO CONTROLLER BASED MULTIPURPOSE SECURITY DEVICE WITH DIRECTION CAPABLE OF SECURING A MILITARY CANTONMENT FROM INTRUDER LOCATION AND DETECTION AND TO CONTROL ACCESS TO A STRONG ROOM IN THE CANTONMENT

 

CHAPTER ONE

 

INTRODUCTION

 

1.1.         Background of the Study

 

The industrial Electronics has changed the whole field of Engineering and technology is occurring so rapidly, even in developing countries. It is so because newer technologies overcome older ones. After the industrial revolution the world shifted towards the information age with the development of computers during the1950’s.

 

As such, mechantronics means the principle that combines the application of mechanical and electrical means has taken over the greater part of industrial electronics which is indispensable in modern technology.

 

In Nigeria, security which is one of the basic lookouts in any productive firm, has been on the decrease. Most industries have gone bankrupt because of their inability to meet up to the security standard required in a modern day setting. Equally, some homes and offices have lost important documents and properties due to easy access that criminals have. There is thus an urgent need for significant security measures to improve the standard of living of the people, enhance development and put to a stop the menace of insecurity. That is the reason as a student of Computer System Engineering the project named “Intruder Detector Alarm System with direction”, was embarked on.

 

1.2       General Description of the Project

 

This electronic system consists of four sensors made up of opto couplers realized with combination of Laser beam, from Laser diode coupled into a cadmium sulfide photocell (C.D.S photocell).

 

This component serves as an electronic eye, the output of opto couplers conditioned by a Schmitt trigger NAND gate control Logic (74 Ls 132) TTL chip. The output of the 132 chips is used to trigger one short delay which reset an astable multi-vibrator which generates the frequency that is used to drive the buzzer alarm. Each of the sensor output is fed to a BCD to decimal priority encoder whose output is decoded to a format that can be displayed using a seven-segment display (common anode).   The buzzer is interfaced through a single transistor static switch.

 

The entire system is designed in such a manner that whenever somebody wants to gain entrance through the back door, the electronic eyes (optocoupler) installed at the locations respectively senses the presence and triggers a buzzer alarm at the security department of the cantonment and seven-segment display shows the exact location of the intruder.

 

1.3     Aim and Objectives of the Project

 

  1. The major aim of this project is to design and implement a microcontroller based multipurpose security device with direction capable of securing a military cantonment from intruder location and detection and to control access to a strong room in the cantonment.

 

  1. Another objective of this project is to ground the graduating student in electronic system design and implementation involving Random logic.

 

  1. This project is also aimed at acquainting the young engineers with skills for engineering, technical and scientific writing which is very indispensable in their professional practice.

 

  1. Another aim of this project is to familiarize these graduating students with electronic system designs that have real life application in industrial security.

 

HOW TO GET THE FULL PROJECT WORK

 

PLEASE, print the following instructions and information if you will like to order/buy our complete written material(s).

 

HOW TO RECEIVE PROJECT MATERIAL(S)

After paying the appropriate amount (#5,000) into our bank Account below, send the following information to 08137701720

(1)    Your project topics

(2)     Email Address

(3)     Payment Name

(4)    Teller Number

We will send your material(s) after we receive bank alert

 

BANK ACCOUNTS

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 0046579864

Bank: GTBank.

 

OR

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 2023350498

Bank: UBA.

 

 

NOTE:

YOU CAN ALSO MAKE A TRANSFER PAYMENT

 

FOR MORE INFORMATION, CALL:

08137701720

 

AFFILIATE LINKS:

www.easyprojectmaterials.com

www.easyprojectmaterials.net.ng

www.easyprojectsmaterials.net.ng

www.easyprojectsmaterial.net.ng

www.easyprojectmaterial.net.ng

www.academia.edu