Show all

THE DESIGN AND CONSTRUCTION OF CAR CONTROLLER USING TELEMETRY SYSTEM

ATTENTION

 

BEFORE YOU READ THE ABSTRACT OR CHAPTER ONE OF THE PROJECT TOPIC BELOW, PLEASE READ THE INFORMATION BELOW.THANK YOU!

 

INFORMATION:

YOU CAN GET THE COMPLETE PROJECT OF THE TOPIC BELOW. THE FULL PROJECT COSTS N10,000 ONLY. THE FULL INFORMATION ON HOW TO PAY AND GET THE COMPLETE PROJECT IS AT THE BOTTOM OF THIS PAGE. OR YOU CAN CALL: 08068231953, 08168759420

 

WHATSAPP US ON  08137701720

 

 

 

THE DESIGN AND CONSTRUCTION OF CAR CONTROLLER USING TELEMETRY SYSTEM

 

 

CHAPTER ONE

 

INTRODUCTION

 

The vehicle system control using telemetry application is all about using a radio wave to control and activate certain events such as the car horn, car head light, car ignition (starter) and car air conditioner etc.

 

This is achieved by using various tone frequencies by using an encoder via a radio frequency transmitter (low power) that provides the carrier frequency for these tones.

 

At the receiver end demultiplexing and decoding of these tone takes place via a detector/receiver stage. The output of the encoder is used to turn on a relay switch, which inturn connects power source to either the car engine, horn or lamp etc.

 

The application of thus project include space exploration, where lunar vehicles are controlled from earth station by using satellite as the medium of transfer of signals.

 

In the military warfare, unmanned air crafts, missiles and even armoured tanks are controlled these days by using the pinaple of telemetry applications. Other areas include GSM, where a subscriber has the total control of his telephone calls conversation through the BTS (Base Transmission or Transceiver Station). Its application are so vast and large that they are too numerous to mention.

 

BLOCK DIAGRAM FOR TRANSMITTER CONTROL UNIT

 

BLOCK DIAGRAM FOR RECEIVER CONTROL UNIT

 

Telemetry system has two units the transmitter and receiver. The link between the two unit is radio wave. The transmitter sends tones of different frequencies the receiver receives the tones.

 

TRANSMITTER

 

Transmitter is a device that process and possibly encode information, so as to make it suitable for transmission and subsequent reception. In a transmitter the information modulates the carrier. It superimposed an a light frequency since wave modulation varies from one system to another and may be high or low levels. Modulations is of three types amplitude modulation, frequency modulation and pulse modulation or combination of these.

 

FREQUENCY MODULATION:

 

Frequency modulation is a system in which the amplitude of the modulated carrier is constant while its frequency and rate of change are varied by the modulating signal. Frequency modulation is much more immune to noise than amplitude modulation noise vector is superimposed on the carrier.

 

 

 

 

 

HOW TO RECEIVE PROJECT MATERIAL(S)

After paying the appropriate amount (#5,000) into our bank Account below, send the following information to

08068231953 or 08168759420

 

(1)    Your project topics

(2)     Email Addressing

(3)     Payment Name

(4)    Teller Number

We will send your material(s) after we receive bank alert

 

BANK ACCOUNTS

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 0046579864

Bank: GTBank.

 

OR

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 3139283609

Bank: FIRST BANK

 

 

 

FOR MORE INFORMATION, CALL:

08068231953 or 08168759420

 

 

AFFILIATE LINKS:

easyprojectmaterials.com

googleprojectsng.blogspot.com

myprojectsng.blogspot.com.ng

https://projectmaterialsng.blogspot.com.ng/

https://foreasyprojectmaterials.blogspot.com.ng/

https://myeasymaterials.blogspot.com.ng/

https://eazyprojectsmaterial.blogspot.com.ng/

https://easzprojectmaterial.blogspot.com.ng/